Page 2 of 2

Posted: Fri Nov 07, 2008 12:41 am
by matts13
a s13 temp sensore on a 14 would make them runned bad. the at in the intake manifold so if you changed them over you good if not start with that.




aslo unplug maf and see how it runs.

please buy a 6 dollar set of plugs and put in too.

did you hook up the fuel lines backwards?

Posted: Fri Nov 07, 2008 3:21 am
by JJ Alfano
yeah, the fuel lines need to be like this:

the line without the fuel filter goes to the fuel pressure regulator

so make sure thats right, and if its not idling, check for vacuum leaks for sure

Posted: Fri Nov 07, 2008 9:55 am
by DriftDuck
I do believe that you need to swap ecu as well... I'm a little foggy on the subject though. we swapped it anyways because we were converting it from auto to manual. or did we... I'll ask around. I have a hard time remembering the swap we did.


other than that I would say gummed up sensor somewhere, like matt was saying.


but really, if it doesn't idle, I would really really reaaaaaally have to say vacuum. Spray carburator cleaner around your vacuum lines and intake manifold and if the RPM increases, thats your leak. of course, have to get it started FOERST. might have to hold down the throttle.

and it could also be ignition timing. if your a few degrees off it will run like absolute garbage and the idle will suffer as well.

Posted: Fri Nov 07, 2008 10:20 am
by blink182house
figured it all out last night guys, got it purring and all back together! thanks for all the help/input, i cant wait to get this car out my garage so I can start working on MINE for once!

Posted: Fri Nov 07, 2008 10:39 am
by charlie
So you're really not going to tell everyone what the solution was?

Posted: Fri Nov 07, 2008 1:07 pm
by DriftDuck
superserial, I need to know.

Posted: Fri Nov 07, 2008 3:36 pm
by blink182house
there was a vacuum line about 3/8" size underneath intake mani that looked like it goes into the thermostat housing inbetween those two water lines just barely slipped off.... probably would've never seen it honestly if we wouldn't have ran the motor a little while and let some oil leak out before fixing the stripped valve cover bolts, got under to check oil and just happened to see it barely! thanks for everyones help and input, im looking forward to moving onto my own car now, after months of work im ready to start wiring it up and crank it over for the FOERST time!

Posted: Fri Nov 07, 2008 4:04 pm
by charlie
little fixes like that are so rewarding when you finally find them. congrats and good luck on ur own car.

Posted: Fri Nov 07, 2008 4:19 pm
by JJ Alfano
charlie wrote:little fixes like that are so rewarding when you finally find them. congrats and good luck on ur own car.

Posted: Fri Nov 07, 2008 8:57 pm
by matts13
so your crank case vent had a vacum leak. i rule. listen to me more.

Posted: Fri Nov 07, 2008 9:02 pm
by charlie
matts13 wrote:i rule.
QFT

Posted: Sat Nov 08, 2008 2:20 am
by Falkon45
well it's kind of hard to tell from the crappy sound, and my shitty speakers, but It's definitely something to do with the timing.

Is there any smoking at all? I know jack about any silvia, other than the s12, but it could be the ecu. If not, and it has a distributor, check the ignitor, and the cap. that same thing happened to my friends crx. Took me a week to figure out. I'm only going off the basic car crap.

Posted: Sat Nov 08, 2008 2:22 am
by Falkon45
oops. I should have finished reading the thread.

Posted: Sat Nov 08, 2008 11:03 pm
by blink182house
matts13 wrote:so your crank case vent had a vacum leak. i rule. listen to me more.
if i would've known what or where that was, it would've helped more. but glad to know you were correct! :wink: